Shopping Cart
(Your shopping cart is empty)

TPMS Links

Find TPMS by Manufacturers

Wholesale & Training








Online Payment Service
Home > TPMS Reset and Relearn > GMC TPMS Reset - Relearn
GMC TPMS Relearn

GM-1

1. Inflate all tires to pressure indicated on tire placard.

2. Turn ignition to ON position (engine off)

3. Press the RESET button found on passenger side instrument panel fuse box.

4. The TPMS telltale will blink 3 times and turn off.

GM-2

1. Inflate all tires to pressure indicated on tire placard.

2. Turn ignition to ON position. (engine off)

3. Press vehicle information button until TIRE INFLATION MONITOR SYSTEM PRESS SWITCH TO RESET is displayed.

4. To reset low tire pressure condition, hold down the DOWN/LEFT arrow button until TIRE INFLATION MONITOR SYSTEM HAS BEEN RESET is displayed. Release DOWN/LEFT arrow button and TIRE PRESSURE NORMAL is displayed.

5. To reset system after tire rotation/replacement, hold down the DOWN/LEFT arrow button for 5 seconds. Release DOWN/LEFT arrow button and TIRE PRESSURE NORMAL is displayed.







GM-3

1. Inflate all tires to pressure indicated on tire placard.

2. Turn ignition to on POSITION (ENGINE OFF).

3. Press GAUGE INFO button until TIRE PRESSURE is displayed.

4. Hold down RESET button until TIRE PRESSURE RESET is displayed.

5. Release RESET button, TIRE PRESSURE NORMAL is displayed.

GM-4

1. Inflate all tires to pressure indicated on tire placard.

2. Turn ignition to ON position. (engine off)

3. Press GAUGE INFO button until TIRE PRESSURE LOW CHECK TIRES is displayed.

4. Hold down RESET button until TIRE PRESSURE NORMAL is displayed.

GM-5

1. Turn ignition to ON position (engine off)

2. Press vehicle information button on the DIC until the message LEARN TIRE POSITIONS is displayed.

3. Press the SET/RESET button to enable vehicle learn mode. The horn will sound twice to indicate the vehicle has entered learn mode and the DIC will display the message TIRE LEARNING ACTIVE.

4. Starting at the LF tire, increase/decrease pressure until horn sounds.

5. After horn sounds, proceed as in step 4 for the next 3 sensors in the following order: RD, RR, LR.

6. After LR sensor has been learned the horn will sound twice, turn ignition to OFF position.

7. Adjust all tires to pressure listed on tire placard.

*if DIC will not enable vehicle learn mode, then see GM-6

GM-6

1. Apply parking brake. Turn ignition to ON position (engine off)

2. Turn headlight switch from OFF to parking lamps 4 times within 4 seconds. A double horn chirp will sound and the TPMS telltale will begin blinking to indicate the learn mode is enabled.

3. Starting at the LF tire increase/decrease pressure until horn sounds.

4. After horn sounds, proceed as in step 3 for the next 3 sensors in the following order : RF, RR LR.

5. After LR sensor has been learned, turn ignition to OFF position. Adjust all tires to pressure listed on tire placard. *If headlight switch does not enable TPMS Learn Mode, use TPMS Learn button on dash.

GM-7

1. Inflate all tires to pressure indicated on tire placard.

2. Turn ignition to ON position (engine off).

3. Hold down MODE button until DIC display reads LOW TIRE PRESSURE HOLD SET TO RESET.

4. Hold down SET button until a chime sounds and TIRE PRESSURE RESET is displayed.

5. System will now sound a chime 3 times, and DIC will display TIRE PRESSURE NORMAL.


GM-8

With standard ignition:

1. Turn the ignition to the ON position (engine off)

2. Using keyless entry system: press and hold lock and unlock button simultaneously until horn sound and release INFO button until TIRE LEARN message is indicated on display. Hold down SET/RESET button until horn sounds. LF turn signal is illuminated to indicate learn mode enabled.

3. Starting with LF tire, increase/decrease the pressure until horn sounds.

4. After horn sounds, proceed as in step 3 for the next 3 sensors in the following order, RF RR LR.

5. After LR sensor has been learned, turn ignition to OFF position. Adjust all tires to pressure listed on tire placard.

With Push-Button start:

1. Press and hold the push start button until the vehicle is in accessory mode. Note: on Cadillac models you will know you are in accessory mode when the Cadillac emblem appears on the DIC.

2. Press the MENU button located on the turn signal lever until “VEHICLE INFORMATION MENU” is displayed.

3. Once you are in the VEHICLE INFORMATION MENU, use the arrows on the signal lever until the DIC displays the vehicle’s tire inflation pressures and positions.

4. Press and hold the button located on the end of the turn signal lever until “ Are you sure that you want to relearn? YES or NO” is displayed.

5. Use the arrows on the signal lever to highlight YES. Once YES is highlighted, press the button located on the end of the turn signal lever. The horn will chirp, “Tire Learning Active” will be displayed on the DIC, and the left turn signal will be illuminated.

6. Beginning with the left front tire, use a TPMS activation tool to activate the LF sensor. Once the sensor has been activated, the horn will chirp and the right turn signal will be illuminated. Repeat procedure in the following order. RF, RR, LR. Once the LR has been activated, the horn will chirp twice. You can then turn the vehicle off to exit “learn mode”.

GM-9

1. Turn ignition to ACC position.

2. Press and hold unlock and lock buttons on the keyless entry transmitter until the horn sounds.

3. Starting with LF tire, increase/decrease the pressure until horn sounds.

4. After horn sounds proceed as in step 3 for the next 3 sensors in the following order: RF, RR, LR. After completing the LR, horn will sound twice.

5. Turn ignition to OFF position to exit vehicle learn mode. Adjust all tires to pressure listed on placard.

GM-10

1. Turn ignition to ACC position.

2. Press and hold unlock and lock buttons on the keyless entry transmitter until the horn sounds.

3. Starting with LF tire, increase/decrease the pressure until horn sounds.

4. After horn sounds proceed as in step 3 for the next 3 sensors in the following order: RF, RR, LR. After completing the LR, horn will sound twice.

5. Turn ignition to OFF position to exit vehicle learn mode. Adjust all tires to pressure listed on placard.

GM-11

1. Apply parking brake. Turn ignition to ON position (engine off)

2. Press and hold unlock and lock buttons on the keyless entry transmitter until horn sounds, and then LF turn signal will become illuminated.

3. Starting with LF tire, increase/decrease tire pressure until horn sounds.

4. After horn sounds proceed as in step 5 for the next 3 sensors in the following order: RF RR LR After completing LR tire horn will sound twice.

5. Turn ignition to OFF position to exit vehicle learn mode. Adjust all tires to pressure listed on the placard.

GM-12

Ensure all tires are inflated to the pressure listed on the tire placard. When ignition is turned off, the system will be cleared and the TPMS telltale will turn off. The system will recalibrate when vehicle is operated at a speed of 30 mph for a minimum of 30 seconds.

GM-13

1. Inflate all tires to pressure indicated on tire placard.

2. Make sure the vehicle has been parked for at least 2 minutes before proceeding.

3. Turn the ignition switch to the ON position (engine off).

4. Press the RESET button the the Driver Information Center (DIC) to clear any warning messages displayed on the Instrument Panel Cluster (IPC).

5. Press and release the OPTIONS button on the DIC until the IPC display is blank.

6. Press and hold the RESET button on the DIC for three seconds.

7. Press and release the OPTIONS button again until the message TIRE TRAINING appears on the IPC.

8. Press and release the RESET button until the message LEARN L FRONT TIRE is displayed.

9. Starting at the LF tire, place relearn magnet over valve stem until horn sounds.

10. After horn chirp has sounded, proceed as in step 8 for the next three sensors in the following order: RF, RR, LR.

GM-14

1. Inflate all tires to pressure indicated on tire placard.

2. Turn ignition switch to the ON position (engine off).

3. Press the RESET button on the DIC to clear any warning messages.

4. Press and release the OPTIONS button on the DIC until the display is blank.

5. Press and hold the RESET button on the DIC for 3 seconds.

6. Press and release the OPTIONS button again until the message TIRE TRAINING is displayed.

7. Starting at LF tire, place relearn magnet over valve stem until horn sounds.

8. After horn chirp has sounded, proceed as in step 6 for the next three sensors in the following orderL RF, RR, LR.

9. Turn the ignition switch to the OFF position to exit the relearn mode.





GM-15

Connect compatible scan tool to Data Link Connector (DLC) and follow directions on tool display.

GM-16

Using Light Switch

1. Inflate all tires to pressure indicated on tire placard.

2. Turn ignition to ON position (engine off).

3. Turn the light switch from OFF to Parking lamps 3 times within 5 seconds.

Using Radio

1. Inflate all tires to pressure indicated on tire placard.

2. Turn ignition to ON position (engine off).

3. Turn radio off.

4. Hold DISP button until SETTINGS is displayed.

5. Use SEEK buttons to scroll down until TIRE MON is displayed.

6. Press the PREV or NEXT buttons until RESET is displayed.

7. Press the DISP button, a chime will sound and DONE is displayed.

8. Scroll until EXIT is displayed, press DISP button, chime sounds to signal exit from learn mode.

GM-17

1. Turn ignition to the ACC position.

2. Press and hold unlock and lock buttons on the keyless entry transmitter until horn sounds and left turn signal is illuminated. Or using the DIC, press and release INFO button until TIRE LEARN message is indicated on display. Hold down SET/RESET button until horn sounds and left turn signal is illuminated.

3. Starting with LF tire, increase/decrease tje pressure until the horn sounds.

4. After horn sounds proceed as in step 4 for the next 3 sensors in the following order: RF, RR, LR. After completing LR tire, horn will sound twice.

5. Turn ignition to OFF position to exit vehicle learn mode. Adjust all tires to pressure listed on tire placard.

GM-18

1. Inflate all tires to pressure indicated on tire placard.

2. Turn ignition to ON position (engine off)

3. Press the RESET button found on the driver’s side instrument fuse panel box.

4. The OIL CHANGE indicator will blink.

5. Press RESET button, CHANGE OIL indicator will turn off and TPMS telltale will blink.

6. Hold down RESET button until a chime is heard and TPMS telltale is no longer displayed.







GM-19

1. Inflate all tires to pressure indicated on tire placard.

2. Turn ignition to ON position (engine off)

3. Press the SELECT right arrow button located on the DIC until GAUGE is displayed.

4. Press SELECT down arrow button to display TIRE PRESSURE.

5. Hold down RESET button until TIRE PRESSURE RESET is displayed.

6. Release RESET button and the message TIRE PRESSURE NORMAL will be displayed.

GM-20

1. Inflate all tires to pressure indicated on tire placard.

2. Turn ignition to ON position (engine off)

3. Hold TIRE RESET button until TPMS telltale begins to blink.

4. Release TIRE RESET button and TPMS telltale will go off.

GM-21

1. Inflate all tires to pressure indicated on tire placard.

2. Turn ignition to RUN position.

3. Press vehicle information button until PRESS TO RESET TIRE PRESSURE is displayed.

4. Hold down SET/RESET button until TIRE PRESSURE RESET is displayed.

GM-22

1. Turn ignition to RUN position.

2. Press and hold unlock and lock button on the keyless entry transmitter until horn sounds.

3. Starting with LF tire, increase/decrease the pressure until horn sounds.

4. After horn sounds proceed as in stop 3 for the next 3 sensors in the following order: RF, RR, LR. After completing LR tire, horn will sound twice.

5. Turn ignition to OFF position to exit vehicle learn mode. Adjust all tires to pressure listed on tire placard.

GM-23

1. Inflate all tires to pressure indicated on tire placard.

2. Start the engine.

3. Press and release the SELECT button on the DIC until GAUGE PAGE appears on the DIC display.

4. Press and release the SELECT button again until the message TIRE PRESSURE LOW is displayed.

5. Press and hold the RESET button on the DIC until the message changes to TIRE PRESSURE NORMAL.

6. Release the RESET button.

GM-24

A properly formatted scan is required for learning new sensors IDs.




GM- 25

WITH STANDARD IGNITION:

1. Apply parking brake.

2. Turn ignition to ON position (engine off)

3. Press the MENU button on the DIC (located on turn signal lever on Camaro and on instrument cluster for all others) until the vehicle's tire pressures are displayed.

4. Press Set/Cir (this button is located at the end of the turn signal lever on Camaro). Vehicle asks “Are you sure that you want to relearn?” Select Yes.

5. Starting at LF tire, decrease air pressure until horn chirps. Repeat procedure for remaining tires in the following order: RF, RR, and LR. After completing LR tire, horn will sound twice.

6. Turn ignition to OFF position to exit vehicle learn mode. Adjust all tires to pressure listed on tire placard.

WITH PUSH-BUTTON START:

1. Press and hold the push button start until the vehicle is in accesory mode. Note: on Cadillac models you will know when you are in accessory mode the Cadillac emblem appears on the DIC.

2. Press the MENU button located on the turn signal lever until “VEHICLE INFORMATION MENU” is displayed.

3. Once you are in the VEHICLE INFORMATION MENU, use the ^ v on the turn signal level until the DIC displays the vehicle’s tire inflation pressure and positions.

4. Press and hold the button located on the end of the turn signal level until “Are you sure that you want to relearn? YES or NO” is displayed.

5. Use the ^ v on the turn signal lever to highlight YES. Once YES is highlighted, press the button located on the end of the turn signal lever. The horn will chirp, “Tire Learning Active” will be displayed on the DIC, and the left front turn signal will be illuminated.

6. Beginning with the left front frire, use a TPMS activation tool to activate the left front sensor. Once the sensor has been activated, the horn will chirp and the right front turn signal will be illuminated.Repeat procedure in the following order, right front sensor, right rear sensor, and finally the left rear sensor. Once the left rear sensor has been activated, the horn will chirp twice. You can then turn the vehicle off to exit “learn mode.”

GM-26

WITH STANDARD IGNITION:

1. Set parking brake.

2. Turn ignition to ON/RUN (engine off)

3. Use the MENU button to select the VEHICLE INFORMATION menu in the DRIVER INFORMATION CENTER (DIC).

4. Use thumbwheel to scroll to the Tire Pressure menu item screen.

5. Press the SET/CLR button to begin sensor matching process. A message requesting acceptance of the process should display.

6. Press the SET/CLR button again to confirm selection.

7. Starting with LF tire, increase/decrease tire pressure until horn sounds, or use TPMS relearn tool to activate each sensor.

8. After horn sounds proceed as in step 5 for the next 3 sensors in the following order: RF, RR, LR. After completing LR tire, horn will sound twice.

9. Turn ignition to OFF position to exit vehicle learn mode. Adjust all tires to pressure listed on tire placard.

WITH PUSH-BUTTON START:

1. Press and hold the push button start until the vehicle is in accessory mode. Note: on Cadillac models you will know when you are in accessory mode the Cadillac emblem appears on the DIC.

2. Press the MENU button located on the turn signal lever until “VEHICLE INFORMATION MENU” is displayed.

3. Once you are in the VEHICLE INFORMATION MENU, use the ^ v on the turn signal level until the DIC displays the vehicle’s tire inflation pressure and positions.

4. Press and hold the button located on the end of the turn signal level until “Are you sure that you want to relearn? YES or NO” is displayed.

5. Use the ^ v on the turn signal lever to highlight YES. Once YES is highlighted, press the button located on the end of the turn signal lever. The horn will chirp, “Tire Learning Active” will be displayed on the DIC, and the left front turn signal will be illuminated.

6. Beginning with the left front frire, use a TPMS activation tool to activate the left front sensor. Once the sensor has been activated, the horn will chirp and the right front turn signal will be illuminated.Repeat procedure in the following order, right front sensor, right rear sensor, and finally the left rear sensor. Once the left rear sensor has been activated, the horn will chirp twice. You can then turn the vehicle off to exit “learn mode.”