Shopping Cart
(Your shopping cart is empty)

TPMS Links

Find TPMS by Manufacturers

Wholesale & Training








Online Payment Service
Home > TPMS Reset and Relearn > Ford TPMS Reset - Relearn
Ford TPMS Relearn

FRD-1

With Standard Ignition.

1. Inflate all tires to pressure listed on tire placard

2. Turn ignition to OFF position and press and release brake pedal.

3. Cycle ignition from OFF to RUN position 3 times, ending in RUN position.

4. Press and release brake pedal.

5. Turn ignition to OFF position.

6. Cycle ignition from OFF to RUN position 3 times, ending in RUN position.

7. Horn will sound once and TPMS telltale will blink once train mode is initiated. If equipped with message center, it will display TRAIN LF TIRE. Place antennae of learn tool on sidewall of LF tire 180 degrees from valve stem to activate sensor. Horn will sound once sensor has been recognized, Repeat step for RF, RR, and LR tires.

8. After training LR tire the message center will display TRAINING MODE COMPLETE. If the vehicle is not equipped with the message center display, successful completion can be verified by turning the ignition to the OFF position and not hearing the horn sound. If the horn sounds, the training procedure must be repeated.

**WITH INTEGRATED KEY FOB (ACTUAL KEY CONTAINED IN KEY FOB) PUSH BUTTON START:

1. With vehicle off, press and release the brake pedal.

2. Using the push button, press and hold the button until the vehicle is in acessory mode (ACC mode).

WARNINGl DO NOT PUSH RELEASE TOO QUICKLY. PUSH - WAIT FOR SOUND - RELEASE.

3. Power off by pushing the button 1 time.

4. Repeat 2 more times, ending in ACC mode.

5. Press and release the brake pedal, then turn vehicle off.

6. Using the push button, press and hold the button until the vehicle is in acessory mode.

7. Power off by pushing the button 1 time.

8. Repeat 2 more times, ending in ACC mode.

9. Horn will sound once and TPMS telltale will blink once train mode is initiated.

10. Starting at LF tire, decrease air pressure until horn chirps. Repeat procedure for remaining tires in the following order: RF, RR, and LR. If equipped with banded sensors, place antennae of learn tool on sidewall of LF tire 180 degrees from valve stem to activate sensor. Horn will sound once sensor has been recognized. Repeat step for RF, RR, and LR tires.

11. After successfully programming the LR tire, the message center should display “TRAINING COMPLETE’

12. Inflate all tires to pressure listed on placard.

***WITH INTELLIGENT ASSIST IGNITION SYSTEM (NO ACTUAL KEY CONTAINED IN KEY FOB):

1. With vehicle off, press and release the brake pedal.

2. Using the push button, press once to turn on, then press again to put vehicle into ACC mode, then press again to turn vehicle off.

3. Repeat 2 more times, ending in ACC mode.

4. Press and release the brake pedal, then turn vehicle off.

5. Using the push button, press once to turn on, then press again to put vehicle into ACC mode, then press again to turn vehicle off.

6. Repeat 2 more times, ending in ACC mode.

7. Horn will sound once and TPMS telltale will blink once train mode is initiated. If equipped with message center, it will display TRAIN LF TIRE.

8. Starting at LF tire, decrease air pressure until horn chirps. Repeat procedure for remaining tires in the following order: RF, RR, and LR. If equipped with banded sensors, place antenne of learn tool on sidewall of LF tire 180 degrees from valve stem to activate sensor. Horn will sound once sensor has been recognized. Repeat step for RF, RR, and LR tires.

9. After successfully programming the LR tire, the msessage center should display “TRAINING COMPLETE”

10. Inflate all tires to pressure listed on tire placard.

FRD-2

1. Inflate all tires to the pressure listed on tire placard.

2. Turn ignition cycle to OFF.

3. Cycle ignition from OFF to RUN position 3 times, ending in RUN position.

4. Press and release brake pedal.

5. Turn ignition cycle to OFF.

6. Cycle ignition from OFF to RUN position 3 times, ending in RUN position.

7. Horn will sound once and TPMS telltale will blink once train mode is initiated. If equipped with message center, it will TRAIN LF TIRE. Place relearn magnet on LF sensor until horn sounds.

8. Proceed as in step 6 for the next 3 sensors in the following order: RF, RR, LR.

9. After training LR, the horn will sound and message center will display TIRE TRAINING MODE COMPLETE, if equipped.

FRD-3

Inflate all tires to the pressure listed on tire placard.

For models without message center:

1. Press and hold odometer reset button until TIRE PRESSURE SET is displayed.

2. Hold button for 3 more seconds.

3. TPMS telltale will begin to blink to signal completion of reset process.

For models with message center:

1. Press and hold SETUP button until RESET FOR SYSTEM CHECK is displayed.

2. Press and hold RESET button until HOLD RESET TO RELEARN is displayed.

3. Press and hold RESET for 3 seconds.

4. TPMS telltale and HOLD RESET TO RELEARN message will blink 3 times to signal completion of reset process.

FRD-4

1. Inflate all tires to the pressure listed on tire placard.

2. Turn ignition to ON position.

3. If not equipped with RESET button:

-Press the Trip/Odometer button until TIRE RESET or CHECK TIRE and RESET appear.

- Press and hold button for 3 seconds until TPMS telltale blinks 3 times and turns off.

4. If equipped with RESET button:

-Press and hold TIRE RESET BUTTON (on instrument panel, behind left side of steering wheel) for 3 seconds. TPMS telltale should blink 3 times and turn off.


FRD-5

*Ford TPMS Relearn Tool (or properly formatted TPMS learn tool) is required following rotation, tire replacement, and sensor replacement. This tool is located in the glove box with the owner's manual.

1. Inflate all tires to pressure listed on tire placard

2. Turn ignition to OFF position and press and release brake pedal.

3. Cycle ignition from OFF to RUN position 3 times, ending in RUN position.

4. Press and release brake pedal.

5. Turn ignition to OFF position.

6. Cycle ignition from OFF to RUN position 3 times, ending in RUN position.

7. Horn will sound once and TPMS telltale will blink once train mode is initiated. If equipped with message center, it will display TRAIN LF TIRE. Place antennae of learn tool on sidewall of LF tire 180 degrees from valve stem to activate sensor. Horn will sound once sensor has been recognized. Repeat step for RF, RR, and LR tires.

8. After training LR tire the message center will display TRAINING MODE COMPLETE. If the vehicle is not equipped with the message center display, successful completion can be verfied by turning ignition to the OFF position and not having the horn sound, if the horn sounds the training procedure must be repeated.